MIDI Solutions Pedal Controller

The Pedal Controller accepts an expression pedal (such as the Yamaha FC7 or Roland EV-5 or any potentiometer connected to a 1/4" stereo phone plug) as an input and generates continuous MIDI data based on its position. The Pedal Controller may be inserted inline at any point in the MIDI data stream, allowing continuous MIDI data to be sent to any device in a MIDI setup.

The Pedal Controller's factory default settings are for it to send CC#7 (volume) on MIDI channel 1, so if this is the message that needs to be sent then no programming is necessary - just insert the Pedal Controller in a MIDI setup and it's ready to use. The Pedal Controller can also be programmed to send other types of MIDI messages, for more info read on...

The Pedal Controller can be programmed to send:

• Aftertouch

The Pedal Controller can be programmed to send Aftertouch in response to the pedal movement. The MIDI Channel is programmable, as well as the minimum and maximum values sent by the Pedal Controller.
 

• Pitch Bend

The Pedal Controller can be programmed to send Pitch Bend in response to the pedal movement. The MIDI channel is programmable, as well as the minimum and maximum values sent by the Pedal Controller. Setting the minimum or maximum value to 40H (no pitch bend effect) allows the Pedal Controller to be used as an "up only" or "down only" pitch bender (it is not recommended to use the full pitch bend range since it is very difficult to find the halfway pedal position needed to bring the pitch to the center value).
 

• Control Change

The Pedal Controller can be programmed to send a Control Change message in response to the pedal movement. The Control Change number is selectable, as is the MIDI channel, and the minimum and maximum values sent by the Pedal Controller.
 

• System Exclusive

The Pedal Controller can be programmed to send a System Exclusive message with one byte that varies in response to the pedal movement. The System Exclusive message can be a maximum of 20 bytes in length, the byte of the message that varies is selectable, as are the minimum and maximum values sent.
 

The Pedal Controller includes a MIDI Echo parameter that is selectable on/off.

The Pedal Controller includes a MIDI Echo parameter which can be programmed to ON or OFF. When MIDI Echo is ON, all MIDI messages appearing at the MIDI In of the Pedal Controller are echoed to its MIDI Out. When MIDI Echo is OFF, messages appearing at the MIDI In of the Pedal Controller are filtered, and not echoed to its MIDI Out.
 

The Pedal Controller accurately tracks the position of the pedal or potentiometer connected to it. Small fluctuations are eliminated when the pedal is in a stationary position and no extraneous messages are sent out. When the pedal is moved slightly, the Pedal Controller will send an update even if its position has only changed by a single value. Many control wheels or knobs only update themselves every two or every four values, resulting in coarser control, and sometimes zipper noise.

Another unique feature of the Pedal Controller is its ability to add a variable amount of curvature to the response of the pedal. This allows you to correct for pedals with nonlinear responses, or to add greater response at one end of the pedal compared to the other.

The Pedal Controller is programmed by sending it MIDI System Exclusive messages (read the Programming FAQs for more details). This is easily done with the MIDI Solutions Programming Tools software. Once programmed, its settings are retained even after power is removed. The Pedal Controller can be reprogrammed with new settings as often as needed. The Pedal Controller's factory default settings are for it to send CC #7 (volume) on MIDI channel 1, with the Echo parameter set to ON.

The Pedal Controller is MIDI-powered, and requires no batteries or power supply to operate with most MIDI products (for more information read the Power FAQs). A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it.

Weight: 124 g (4.4 oz.)
Dimensions: 112 x 62 x 31 mm (4.4" x 2.4" x 1.2")

MIDI Solutions Pedal Controller Block Diagram:

Learn more about the MIDI Solutions Pedal Controller

• Programming Tools software - spending a few minutes with the Programming Tools software is an excellent way to become familiar with the capabilities of the Pedal Controller

• Pedal Controller Application Examples
  

• Pedal Controller Operating Instructions
  

• How to order the MIDI Solutions Pedal Controller

• Questions? Send us an email: info@midisolutions.com

 

---

Products | FAQs | Support | About | Order


Copyright © 2024 MIDI Solutions Inc.